Technical Articles Collection

A.C. Spowage and S. Bray in Characterisation of Nanoprecipitation Mechanisms During Isochronal Ageing of A Pseudo Binary AL-8.7LI AT % Alloy, IMM Newsletters, Institute of Materials, Malaysia, Vol. June 2009, Issue 18, pp. 10-14. [Full paper]

A.C Spowage, N. P Brewitt and J.W. Lee in The Scanning Electron Microscope-A Tool for the Failure Investigator, IMM Newsletters, Institute of Materials, Malaysia, Vol. July 2010, Issue 20, pp. 11-13. [Full paper]

S. N. A. Razak, A. R. Othman, L. W. Sheng in Effect of Temperature on the Strength Properties of Adhesively Single-Lap Bonded Joint for Composite Laminates, Materials Mind, Vol. February 2013, Issue 1, pp 4-6. [Full paper]

C. K. Abdullah, M. Jawaid, H.P.S. Abdul Khalil and M.R. Nurul Fazita in Oil Palm Trunk Biocomposite: Mechanical and Morphological Properties, Materials Mind, Vol. February 2013, Issue 1, pp 6-8. [Full paper]

Y. Mubarak Sani, A. B. Ayu Haslija and S. Noor Rosyidah in Incorporation of Rice Straw Into Clay Bricks, Materials Mind, Vol. February 2013, Issue 1, pp 9-11. [Full paper]

F.-L. Pua, S. M. Sapuan and A. Kumaran in Study of Cocoa Pod Husk / Polyvinyl Alcohol (PVA) as A New Biodegradable Composite Film, Materials Mind, Vol. February 2013, Issue 1, pp 11-13. [Full paper]

M. A. Nurnisham in Extending the Service Life of Crude Oil Export Line using PIPEASSURE™ Composite Overwrap Repair System, Materials Mind, Vol. February 2013, Issue 1, pp 14-18. [Full paper]

S. N. Surip in Innovative Green Material From Natural Fiber Reinforced Bio-Plastic Composite, Materials Mind, Vol. April 2013, Issue 3, pp 14.[Article]

M. K. Talari and M. K. Harun in Materials Are Getting Smarter, Materials Mind, Vol. April 2013, Issue 3, pp 23-24.[Full paper]

M. A. Billingham, M. Haines, C.-H. Lee and L. Smith in Corrosion and Materials Selection Issues in Carbon Capture Plants, Materials Mind, Vol. April 2013, Issue 3, pp 26-31.[Full paper]

K. C. Chew, C. H. Lim in FT-IR Fingerprinting of Organic Coatings: Possibilities and Practicalities in Industry, Materials Mind, Vol. April-September 2013, Issue 4, pp 19-21.[Full paper]

S. N. H. Razali, N. Ghazali, M. R. Johan in Metallic Nanoparticles and Its Primary Future, Materials Mind, Vol. April-September 2013, Issue 4, pp 21-23.[Full Paper]

A. S. M. Goh in Inverse Identification of Constitutive Properties, Materials Mind, Vol. April-September 2013, Issue 4, pp 24-26.[Full Paper]

C. H. Chan and Y. Y. Teo in Fourier-transform Infrared Analysis of Polymeric Coatings as Benchmark for Paint Industry, Materials Mind, Vol. October-December 2013, Issue 5, pp 21-23.[Full Paper]

A. Rein and J. Seelenbinder in Composite Thermal Damage – Correlation of Short Beam Shear Data with FTIR Spectroscopy Portable, Non-destructive Analysis, Materials Mind, Vol. October-December 2013, Issue 5, pp 24-25.[Full Paper]

H. Hermawan in Introduction to Metals for Medical Devices, Materials Mind, Vol. October-December 2013, Issue 5, pp 34-38.[Full Paper]

M. K. Harun and I. Ismail in Cathodic Disbonding Dominates Rubber/Mild Steel Composite Failure in Marine Environment, Materials Mind, Vol. January-March 2014, Issue 6, pp 23-26.[Full Paper]

C. H. Chan, C. H. Ong, W. Tan, M. K. Harun, J. Y Lee in FTIR Structural Analysis of Epoxy Paints on Steel Structure for Coating Fingerprinting Certificate as Benchmark for Paint Industry, Materials Mind, Vol. April-June 2014, Issue 7, pp 29-36.[Full Paper]

C. P. Way, W. Tan and C. H. Chan in ATR-FTIR: A Simple and Rapid Tool For Coating Fingerprinting, Materials Mind, Vol. April-June 2014, Issue 7, pp 38-41.[Full Paper]

C. H. Chan, C. H. Ong, W. Tan, M. K. Harun, J. Y Lee in Compare Functions of FTIR Software for Structural Analysis of Epoxy Paints on Steel Structures for Coating Fingerprinting Certificate, Materials Mind, Vol. July-September 2014, Issue 8, pp 25-29.[Full Paper]

K. C. Chew in Analysing Organic Coatings, Materials Mind, Vol. January 2015, Issue 9, pp 27-28.[Full Paper]

M. H. A. Malek, S. K. Abas, N. H. Saad and N. M. Shah in Performance Analysis of 99.5% Aluminium Alloy as A Sacrificial Anode, Materials Mind, Vol. July 2015, Issue 11, pp 20-24.[Full Paper]

S. Morra and M. Scasso in Economical Aspect of Efficient Process Control in Welding Fabrication, Materials Mind, Vol. January 2016, Issue 13, pp 54-57.[Full Paper]